Fabricante: Jung
Referencia 1: 2214 REG A
Referencia 2:
Serie:
Color: -
G.D.: 16
Peso: 0,200 Kg.
Código Web: 5448

ENTRADA ANALÓGICA, 4 CANALES

P.V.P.:   Identifíquese para ver precios
G.D. Futurasmus:
  DESCRIPCIÓN
KNX analog input 2214 REGA
ETS-product family: Input
Product type: 4-gang analog input
Series embodiment (SE)-device (4 units)

The analog input processes measured-value data supplied by analog sensors. Four analog transducers in any combination can be connected to the input. The analog input evaluates voltage and current signals.
Voltage signals: 0 ... 1 V DC 0 ... 10 V DC
Current signals: 0 ... 20 mA DC 4 ... 20 mA DC
The 4 ... 20 mA current inputs can be monitored for open-circuit conditions.
The following sensors from the JUNG range can be connected to the analog input: Brightness (WS 10 H), Twilight (WS 10 D), Temperature (WS 10 T), Wind (WS 10 W) and Rain (WS 10 R).

An optional analog input extension module, ref.-no. 2214 REGAM, connected by a 6-pole system connector adds four more analog sensor inputs to the device. A 6-pole connector can be used for future extensions.

The measured values are encoded by the analog input in the form of value telegrams (DPT 9.0xx, 2 byte or DPT 5.001, 1 byte) so that other bus subscribers (e.g. visualization software, Info Display) can display these measured values, generate messages or intervene in automatic control processes.

Each measured value has two presettable limit values. As soon as a measured value rises above or drops below these limits, the analog input can transmitt the corresponding messages. The limit values can also be modified in operation by other devices as, for instance, a push-button sensor serving as a value transmitter.

The analog input needs 24 V AC for operation. This voltage can be supplied, for instance, by the power supply unit (WSSV 10). This power supply unit can at the same time also supply the power for wind sensor heating or the power for a connected analog input extension module.

The terminals US and GND supply 24 V DC (max. 100 mA altogether) to external analog sensors. In the event of short-circuits or overload between US and GND, the power is shut off.

KNX analog input 2214 REGA
ETS-product family: Input
Product type: 4-gang analog input
Series embodiment (SE)-device (4 units)
The analog input processes measured-value data supplied by analog sensors. Four analog transducers in any combination can be connected to the input. The analog input evaluates voltage and current signals.
Voltage signals: 0 ... 1 V DC 0 ... 10 V DC
Current signals: 0 ... 20 mA DC 4 ... 20 mA DC
The 4 ... 20 mA current inputs can be monitored for open-circuit conditions.

The following sensors from the JUNG range can be connected to the analog input:
Brightness (WS 10 H), Twilight (WS 10 D), Temperature (WS 10 T), Wind (WS 10 W) and Rain (WS 10 R).
An optional analog input extension module, ref.-no. 2214 REGAM, connected by a 6-pole system connector adds four more analog sensor inputs to the device. A 6-pole connector can be used for future extensions.

The measured values are encoded by the analog input in the form of value telegrams (DPT 9.0xx, 2 byte or DPT 5.001, 1 byte) so that other bus subscribers (e.g. visualization software, Info Display) can display these measured values, generate messages or intervene in automatic control processes.

Each measured value has two presettable limit values. As soon as a measured value rises above or drops below these limits, the analog input can transmitt the corresponding messages. The limit values can also be modified in operation by other devices as, for instance, a push-button sensor serving as a value transmitter.

The analog input needs 24 V AC for operation. This voltage can be supplied, for instance, by the power supply unit (WSSV 10). This power supply unit can at the same time also supply the power for wind sensor heating or the power for a connected analog input extension module.

The terminals US and GND supply 24 V DC (max. 100 mA altogether) to external analog sensors. In the event of short-circuits or overload between US and GND, the power is shut off.

Technical data
KNX Supply
Voltage: 21 - 32 V DC (SELV)
Power consumption: typically 150 mW
Connection: Bus terminal (KNX Typ 5.1)
External supply, voltage: 24 V AC ± 10 %
Current consumption: 250 mA max.
Power consumption: max. 4 VA
Connection: Screw terminals: 0.5 mm2 to 4 mm2, single-wire
0.34 mm2 to 4 mm2, fine-wire (without ferrule)
0.14 mm2 to 2.5 mm2, fine wire (incl. ferrule)
Response to voltage failure
Bus voltage only: No communication with KNX.
Operating voltage only: No communication with KNX, no feeding of the measuring sensors.
Bus and mains/operating voltage: No communication with KNX, no feeding of the measuring sensors.
Response to recovery
Bus voltage only: No communication with KNX, no feeding of the measuring sensors.
Operating voltage only: No communication with KNX.
Bus and mains/operating voltage: Communication with KNX according to initialization parameters.
Module connection
Numbers: 1
Connection: 6-pole system connector for analog input extension module
Analog inputs
Number: 4
Signal voltage/current: 0 ... 1 V DC, 0 ... 10 V DC, 0 ... 20 mA DC or 4 ... 20 mA DC,
depending on parameterization
Input resistance: Voltage measurement: approx. 18 kO
Current measurement: approx. 100 O
Connection: Screw terminals: 0.5 mm2 to 4 mm2, single-wire
0.34 mm2 to 4 mm2, fine-wire (without ferrule)
0.14 mm2 to 2.5 mm2, fine-wire (incl. ferrule)
Measuring sensor power supply outputs
Number: 2
Rated voltage: 24 V DC ±10 %
Rated current: 100 mA DC (total)
Connection: Screw terminals: 0.5 mm2 to 4 mm2, single-wire
0.34 mm2 to 4 mm2, fine-wire (without ferrule)
0.14 mm2 to 2.5 mm2, fine-wire (incl. ferrule)
Protection: IP 20
Safety class: III
Mark of approval: KNX/VDE
Ambient temperature: -5°C ... +45°C
Storage/transport temperature: -25°C ... +70°C (storage above +45°C reduces the lifetime)
Mounting position: any
Minimum distances: none
Fastening: on DIN rail 35 x 7.5



CATÁLOGOS ESPECIALES KNX
Estética Pulsadores 360º
Pulsadores
Smart Metering
Catálogo MDT 2017
Simulador Iddero Verso

APRENDE
Webinars gratuitos
Tutoriales uBrick
Video Tutoriales CBSE


PARTICIPA
Trivial µBrick
Trucos y consejos KNX
PRUEBA
Test gratutito visualización CBSE

ÚLTIMAS NOTICIAS KNX
Todas las noticias

ÚLTIMAS OFERTAS KNX
Todas las ofertas
DESCARGAS
KNX - Todas las marcas

FUTURASMUS KNX GROUP
Contacto
Dónde estamos
Futurasmus en el mundo
SÍGUENOS
YouTube Channel
Facebook
LinkedIN
Google+
Twitter

CENTRO DE FORMACIÓN KNX++
Futurasmus Zentrum

KNX TEST LAB CERTIFICADO
Futurasmus KNX Lab
MAYORISTA KNX ESPECIALIZADO CENTRO DE FORMACIÓN CERTIFICADO KNX
Futurasmus KNX Group es un mayorista KNX altamente especializado y activo a nivel internacional, siendo nuestro punto fuerte el excelente soporte técnico que ofrecemos. Puede visitar nuestro catálogo online en esta web, y si es un profesional del sector, pedir presupuesto sin compromiso para sus proyectos KNX. Si está interesado en comprar componentes KNX, le invitamos a leer nuestras Condiciones Generales de Venta y ponerse en contacto con nuestros agentes comerciales y técnicos por teléfono, e-mail o chat on-line. Desde 2003 somos Centro de Formación Certificado KNX++, que significa que estamos autorizados para impartir el Curso Básico KNX así como el Curso Avanzado KNX y el Curso de Tutor KNX. Somos independientes de fabricantes y también ofrecemos otros seminarios KNX especializados y monográficos. Tras haber formado a más de 1.500 KNX Partners, nuestros KNX Trainers tienen una amplia y positiva experiencia. Por favor, contacte con nosotros para cursos KNX personalizados (grupos de al menos 8 personas) en cualquier lugar del mundo (español, inglés y alemán).
USO DE COOKIES

Una cookie o galleta informática es un pequeño archivo de información que se guarda en su navegador cada vez que visita nuestra página web.

La utilidad de las cookies es guardar el historial de su actividad en nuestra página web, de manera que, cuando la visite nuevamente, ésta pueda identificarle y configurar el contenido de la misma en base a sus hábitos de navegación, identidad y preferencias.

Las cookies pueden ser aceptadas, rechazadas, bloqueadas y borradas, según desee. Ello podrá hacerlo mediante las opciones disponibles en la presente ventana o a través de la configuración de su navegador, según el caso.

En caso de que rechace las cookies no podremos asegurarle el correcto funcionamiento de las distintas funcionalidades de nuestra página web.

Más información en el apartado “POLÍTICA DE COOKIES” de nuestra página web.